A Beginner's Guide to Installing a Bathtub
A Beginner's Guide to Installing a Bathtub
Blog Article
We've uncovered this post involving Installing A Bathtub listed below on the internet and felt it made good sense to share it with you on this site.
Installing a bath tub isn't specifically rocket science, but it does call for strong plumbing, carpentry, and also occasionally, tiling skills. Changing an old tub with a new one is also a reasonably tough project. If the old bathtub is readily obtainable, the job can relocate easily; if you have to open up a wall to eliminate the old tub and position the new bath tub, the task is much harder. In either case, the job is within a house handyman's abilities, although you will certainly require an assistant to move out the old bathtub and also set in the new one. See to it you have actually qualified yourself for the job as well as fit trying it. As opposed to working with a contractor to take control of a halfway-completed job, it is much better to think about utilizing one before you start. Chances are you might require a specialist plumber to make tube links.
This post will assist you install a new bath tub in your washroom if you have actually currently purchased a new bathtub as well as don't require to alter the arrangement of your previous water supply pipelines.
Your tools and product checklist need to consist of the following:
Planning for the Setup
First of all, the supporting frame supplied with the bath ought to be fitted (if needed) according to the producer's guidelines. Next, fit the taps or mixer to the bath tub. When suitable the faucet block, it is important to ensure that if the faucet includes a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the faucets system to avoid stress on the tub.
Fit the flexible tap adapters to the bottom of both faucets utilizing 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet through the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you make use of all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bath need to now prepare to be suited its final setting.
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your setup, then the first thing you need to do is detach the supply of water. After doing so, switch on the taps to drain any type of water staying in the system. The process of removing the existing taps can be rather troublesome due to the restricted access that is often the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the taps. Have a towel prepared for the remaining water that will certainly come from the pipes. As soon as the supply pipelines have actually been eliminated, make use of the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from transforming during this process. When the taps have been gotten rid of, the holes in the bath/basin will have to be cleansed of any old sealing compound.
Prior to moving on to fit the new taps, compare the pipeline links on the old faucets to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new taps to fit.
Installing the Bath tub
Using both wood boards under its feet, place the tub in the needed setting. The wooden boards are practical in equally spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto 4 little points.
The following objective is to make sure that the tub is leveled all round. This can be achieved by examining the spirit level and readjusting the feet on the tub until the level reads degree.
To install faucets, fit the bottom of the outermost flexible tap adapter to the suitable supply pipeline by making a compression join; after that do the same for the various other tap.
Turn on the water supply and also inspect all joints and brand-new pipework for leaks and tighten them if essential. Fill the bathtub as well as also inspect the overflow electrical outlet and the normal outlet for leaks.
Lastly, take care of the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and securing around the bath tub should wait till the bath tub has actually been made use of at the very least when as this will settle it into its last placement.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will need a plastic adapter to avoid damage to the string. One end of the port fits on the plastic tail of the tap and also the various other end provides a link to the existent supply pipes.
If you require to fit a monobloc, then you will need lowering couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, place the tap in the mounting hole in the bath/basin guaranteeing that the washing machines remain in area in between the tap and also the sink. Protect the faucet in place with the manufacturer offered backnut. As soon as the tap is firmly in place, the supply pipes can be connected to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with normal faucet connectors. The previous kind must be attached to the tap ends initially, tightening up only by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the location where the bathroom satisfies the tile, it is required to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to fracture a stiff seal, causing the water to permeate the wall in between the bath and also the tiling, leading to difficulties with dampness and also possible leakages to the ceiling below.
You can select from a selection of coloured sealants to assimilate your fixtures as well as installations. They are sold in tubes as well as cartridges, and also are capable of securing voids approximately a width of 3mm (1/8 inch). If you have a bigger void to load, you can load it with twists of soaked newspaper or soft rope. Bear in mind to constantly fill the tub with water prior to sealing, to enable the movement experienced when the tub remains in use. The sealer can break rather very early if you do not think about this movement prior to securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also easily readily available on the marketplace. It is suggested to fit the floor tiles utilizing water-resistant or water resistant sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a passionate person who reads about A Step-by-Step Guide to Installing a Bathtub, I assumed sharing that post was a good idea. Make sure you take the time to share this blog post if you liked it. Thanks a bunch for your time. Please come visit our site back soon.
Drains blocked? Dial. Report this page